Radar is a system that uses radio waves to determine the distance, directiond, and radial velocity of objects relative to the site. It is a radiodetermination method[1] used to detect and track aircraft, ships, spacecraft, guided missiles, motor vehicles, weather, and terrain.
5
The SD standard was introduced in 1999 by SanDisk, Panasonic, and Toshiba as an improvement on MultiMediaCards. In 2000, they formed the SD Association, a non-profit organization to create and promote SD Card standards. As of 2023, the SDA has about 1,000 member companies.
21
A SD Card uses flash memory technology to store data. Flash memory is a type of non-volatile storage that retains data even when the power is off. When you save data on a card, it is written into the flash memory cells using electrical charges. Cont. here ecs.page.link/Gy2mT
10
Secure Digital, officially abbreviated as SD, is a proprietary, non-volatile, flash memory card format the SD Association (SDA) developed for use in portable electronic devices such as digital cameras, camcorders, video game consoles, and mobile phones. They come in two sizes.
13
There are many types of audio cables including:
RCA (carry unbalanced signals used for DJing and DVD players)
XLR (carry balanced signals that produce a clean sound even over long cables)
TRS (carries 2 separate channels mainly used for headphones or stereo line level outputs)
4
An audio cable is designed to carry audio signals between devices, consisting of two or more conductors surrounded by insulation and protective covering. The audio cable category is broad and includes many types of wires and connectors for amplifiers, speakers, etc.
Check out our #youtube channel for a new video:
East End Assemblies monkeylink.co/edfbff
#motivation #inspiration #SuccessPath
Inspiration and Lessons learned 30 - Glen Chin. #eastendassemblies #electricalindustry 🚀 #BusinessWisdom #SuccessPath
9
5 more big tips for desoldering:
Minimize time Components & Board are at high temps
Match your Solder Wick Width to Contact Pad
Match Soldering Iron Tip to Braid Width
Clip used Desolder Wick after use
Match flux to cleaning process: (3 types are Rosin, Unfluxed, and No Clean)
8
If you're a beginner, the most straightforward technique (though rigorous) is grinding and scraping. This involves the use of a scraper, knife, or pick and a bit of elbow grease. One can expedite the process with mechanical erasers.
1
To understand some tips, one must first know what tools can be used for desoldering. While there's a variety of tools & companies, here are the main tools you'll need:
Soldering Iron
Soldering Wick
Desoldering Braid & Iron
Desolder Pump and Iron
Power Desoldering Station
8
Key design parameters for power amps are frequency response, gain, noise, and distortion. These are interdependent; increasing gain often leads to undesirable increases in noise and distortion. While negative feedback actually reduces the gain, it also reduces distortion.
6
While the input signal to an audio power amplifier may measure only a few hundred microwatts, its output may be vary based on its use; from a few watts for small consumer electronics devices, to several thousand watts for a nightclub or tens of thousands of watts for a concert.
2
An audio power amplifier low-power electronic audio signals, like from electronic radios or instruments, to a level that is high enough for driving loudspeakers or headphones. In all sounds systems, it's the final stage in a typical audio playback. power
6
Electric Piano can refer to any of the following:
Struck strings (grand/upright with strings and hammers)
Struck reeds (flat steel reels struck by felt hammers)
Struck tuning-forks (2 vibrating parts)
Plucked reeds (saturated leather strike metal reeds)
10
An electric piano is a musical keyboard where sound is produced by means of mechanical hammers striking metal strings or reeds or wire tines leading to vibrations which are then converted into electrical signals by pickups that are connected to an amplifier & loudspeaker.
5
Because of the sophistication of electronic instruments, East End Assemblies has been given jobs in music. Take the keyboard or electric piano. Essentially a computer you play, the keys can hold more extensive sounds as well as be more portable than a grand piano.
3
For successful use of a stencil, its thickness must be properly calculated; otherwise, the paste could be held by the inner walls of the aperture leading to the board to not work. Here is a formula for deciding on your stencil's thickness #smtstencil #designformanufacture #pcb
9
There are 5 keys to the design features of stencils:
Thickness, Aperture Designs, Alignment, Stencil Material & Mounting, and its specific design to a PCB. #pcbassembly #smtstencil #designformanufacture #eastendassemblies
13
For Surface Mount Technology, a stencil is a thin sheet of material with a series of holes cut into it which suit the PCB it'll be used for. This is used to accurately place the correct amount of #solder onto the surface mount pads. #SMT #pcbassembly #stencil #eastendassemblies
24



















































