Qs Lanre ๐Ÿ‘ท๐Ÿพโ€โ™‚๏ธ (@lanrycool) header
Qs Lanre ๐Ÿ‘ท๐Ÿพโ€โ™‚๏ธ (@lanrycool) profile picture

Project Manager | Cost Engineer | Construction Expert | Interior design | Construction reality

Joined December 2010
The way these wooden joints are put together is completely wrong, meaning the weight isn't flowing safely down to the ground.
3
1
3
4,902
This will it work without checking your plumb lines first and protect your sharp corners.
1
7
14,305
How to use vacuum line jetting to for complex conduit runs in seconds.
Hanging ventilation units, speakers, or smart HVAC diffusers directly from lightweight drywall or stretch ceilings without structural independent suspension leads to sagging, acoustic rattling and joint failure.
6
6,511
Angle grinder
Whenever two different wall textures or colors meet at an inside corner, hold a wide putty knife flat against the finished wall to protect it while you sand the adjoining wall with a sanding block.
2
4
79
39,263
Smooth plaster is useless if it isn't flat and plumb
3
1
10
7,931
Use that special square cutter to mark out your exact box boundary, and then switch to a narrow flat chisel to clear out the middle. That way your electrical box fits well into the wall with just a tiny 2mm gap all around.
Stop hacking into newly rendered blockwork with heavy hammers and vibrating sledgehammers that shatter bricks, fracture structural mortar joints and ruin perfectly plumb walls just to bury a switch box or conduit pipe. โ€‹A professional installation requires a controlled, mechanical approach that keeps wall integrity intact, eliminates wide openings and leaves a clean channel ready for conduits.
4
7
134
799,294
Always put your plumbing and electrical pipe sleeves into position along with metal support bars before you pour any concrete. If you need to drill through an existing concrete beam later, use a scanner first to check where the iron rods are so you don't hit them.
3
1
12
13,496
Qs Lanre ๐Ÿ‘ท๐Ÿพโ€โ™‚๏ธ retweeted
ู…ุญุชุฑู ููŠ ุงู„ููƒู‘โ€ฆ ูˆู„ุง ูŠุตูู‘ูŠ ุญุณุงุจู‡ ู…ุน ุงู„ู…ู‚ุงูˆู„ุŸ ๐Ÿ˜…
28
7
1
69
105,786
How to install chemical anchor stud?
1
1
21
13,648
When you take the extra time to cut clean, exact channels for your LED strip lights instead of just slapping them up roughly, it completely changes how the lighting looks. Precision cutting turns basic light bulbs or strips into a high end luxury feature that looks neat, professional and expensive.
2
22
13,746
What's the most expensive mistake you have seen on a job site?
147
Stop hacking into newly rendered blockwork with heavy hammers and vibrating sledgehammers that shatter bricks, fracture structural mortar joints and ruin perfectly plumb walls just to bury a switch box or conduit pipe. โ€‹A professional installation requires a controlled, mechanical approach that keeps wall integrity intact, eliminates wide openings and leaves a clean channel ready for conduits.
17
29
2
484
1,301,173
Upgrade your site setting out from manual string lines to lasers for repeatable and single man precision.
A non-destructive ferromagnetic mounting track for compact cross-line lasers Can be used when working over finished drylining or tiled surfaces.
2
15
5,527
Stages of substructure tanking & mechanical protection.
Waterproofing a foundation or underground wall from the outside is always much better than waterproofing it from the inside. That is because the weight of the underground water actually pushes the waterproof layer tighter against the concrete wall, instead of pushing through the wall and peeling the coating right off from behind. However, if you cut corners when preparing the bare concrete surface or ignore safety inside the deep trench, even the best waterproofing method becomes a dangerous and expensive failure waiting to happen.
1
2
6
2,636
where the metal frame connects to the concrete is the most critical spot on the whole roof and if you cut corners there, the roof can fail.
1
4
21
13,398
Stop treating home power like a random mix of loose wires. You need to design the whole electrical system as one connected setup, from protecting your underground cables so they don't rust in the ground, all the way to the smart automatic switches on the wall that seamlessly handle your grid, inverter and generator power.
1
2
488
To get a wall finish with zero blemishes and no ugly patch lines, hang shade nets over the sunny sides of the scaffolding so the render doesn't bake and dry too fast. Put one worker on each scaffolding level and have everyone move across together from corner to corner while the material is still wet. Finally, peel off your orange tape right away before the render dries so you get a clean and sharp edge.
Stiff broom to splash a rough cement and sand slurry to let it dry into hard and rough teeth. -No plaster gauge/beacon
1
2
17
12,251